The Arduino Pro WisGate Edge Pro powered by RAKwireless™ ensures secure and reliable connectivity for a wide range of professional applications and is suitable for medium-sized to wide area coverag...

Grove - Servo is used in driving mechanism of robots. The module is a bonus product for Grove lovers. We regulated the three-wire servo into a Grove standard connector. You can plug and play it as ...

This is a photoelectric water liquid level sensor that operates using optical principles. The advantages of this photoelectric water liquid level sensor are good sensitivity and no need for mechani...

The resistance of a thermistor will increase when the ambient temperature decreases. It’s this characteristic that we use to calculate the ambient temperature. The detectable range of this sensor i...

Grove-Temperature & Humidity Sensor Pro is a high accuracy temperature and humidity sensor based on the DHT22 module (also known as AM2302 or RHT03). High-cost performance and high precision ma...

The sensor(chip) used in the module is designed with Sensirion’s CMOSens® technology. The chip is well calibrated, linearized and compensated for digital output. The typical accuracy of this module...

Plastic package containing 10 pieces of the following horizontal mount trimmer values: 500 ohm (501) 1 kohm (102) 2 kohm (202) 5 kohm (502) 10 kohm (103) 20 kohm (203) 50 kohm (503) 100 k...

Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator ...

The Arduino 4 Relays Shield is a solution for driving high power loads that cannot be controlled by Arduino's digital IOs, due to the current and voltage limits of the controller. The Shield featur...

The piezo can be connected to digital outputs, and will emit a tone when the output is high. Alternatively it can be connected to an analog pulse-width modulation output to generate various tones a...

Through it, you can control a circuit of high voltage with low voltage, say 5V on the controller. There is an indicator LED on the board, which will light up when the controlled terminals get closed.

Plastic case organized in compartments containing 300 LEDs of 3 and 5 mm with assortment in red, blue, yellow, green and white colors. 40 LEDs per color of 3mm, 20 LEDs per color of 5mm.

Ideal for use with experimental boards! The wires are separable for ease of use.

Ideal for use with experimental boards!

The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial po...

Most ultrasonic distance sensors aren't waterproof which can be a problem if you need your project to withstand the elements outdoors. No need to worry any more! This is a waterproof & ultrason...

Ultrasonic sensors emit ultrasonic pulses, and by measuring the time of ultrasonic pulse reaches the object and back to the transducer, the distance of sensor from the target object is calculated. ...

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x). It has more or less the same functionality of the Arduino Duemilanove, but in a diffe...

The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pin...

The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pin...

It can detect the change in capacitance when a finger is nearby. This means no matter if your finger directly touches the pad or just stays close to the pad, the Grove - Touch Sensor will output HI...

This module is equipped with 4 relays that allow you to activate/deactivate the load connected to them 240V/10A max. It has optoisolated inputs and status LEDs.

This module is equipped with 1 relay that allows you to activate/deactivate the load connected to it 240V/10A (max). The relay is activated by connecting the positive to 5 volts to the “S” pin.

The MKR Relay Protoshield allows you to easily add relays to your MKR board based project. The shield provides two relays (Datasheet)  called RELAY1 and RELAY2 commanded by pin 1 and pin 2 r...