Skip to content

    Your cart is empty

    Time to spark some excitement 🛒⚡

Taxes and shipping calculated at checkout
Subtotal €0,00

Solar Panel Charge Controller - 10 A

SKU TPX00180 Barcode 7630049204454 Show more
Original price €0
Original price €17,07 - Original price €17,07
Original price
Current price €17,07
€17,07 - €17,07
Current price €17,07
VAT included

Charge controller for photovoltaic applications controlled by a microcontroller and capable of operating automatically at both 12 and 24 V.

Overview

It allows to provide the right degree of current to the batteries protecting them from an excess of discharge or charge in order to prolong their life cycle as much as possible.

Attention! use only with 12 and 24 V solar panels.

It protects the battery from polarity reversal, automatically enters protection and locks when the load current exceeds the regulator’s range. In case of short circuit, it enters protection and it overload protection.

To avoid complete battery discharge, the regulator will automatically disconnect the load at a certain voltage that cannot be less than 11.2 V for the 12 V battery and 22.4 V for the 24 V batteries. 


Tech specs

  • Nominal voltage: 12 V / 24 V automatic detection
  • Maximum current: 10 A
  • Maximum solar panel input voltage: 41 V
  • Cut-off voltage: charged battery: 13 V (at 12 V) - 26 V (at 24 V) discharged battery: 11.2 V (at 12 V) - 22.4 V (at 24 V)
  • Reconnection voltage: 13 V (at 12 V) - 26 V (at 24 V)
  • Voltage drop: < 170 mV
  • Dimensions (mm): 133x70x35
  • Weight: 150 g

Conformities

The following Declarations of Conformities have been granted for this board:
CE
For any further information about our certifications please visit docs.arduino.cc/certifications

Get Inspired

PROJECT HUB
Claw prosthesis controlled by myoelectric sensor
Claw prosthesis controlled by myoelectric sensor
Project Tutorial by luiz_coppini

Print a claw on your 3D printer and use a myoelectric sensor to control it.

read more
BLOG
Your Arduino Nano ESP32 can run Doom
Your Arduino Nano ESP32 can run Doom
September 12, 2023

"But can it run Doom?" is more than just a joke in the tech world. It is also a decent litmus test for the computing power of hardware. That test isn't very relevant for modern computers, but it is still worth asking when discussing microcontrollers. Microcontrollers vary in dramatically in processing power and memory, with models to suit every application. But if you have an Arduino Nano ESP32 board, you can run Doom as Naveen Kumar has proven. The Nano ESP32 is a small IoT development board for the ESP32-S3 microcontroller, featuring Wi-Fi® and Bluetooth® connectivity. It also has a relatively high clock speed and quite a lot of memory: 240MHz and 512kB SRAM, respectively. That still isn't enough to meet the requirements of the original Doom release, which needed a lot more RAM. But Kumar demonstrates the use of an MCU-friendly port that runs well on this more limited hardware. Want to give it a try yourself? You'll need the Nano ESP32, an Adafruit 2.8" TFT LCD shield, an M5Stack joystick, a Seeed Studio Grove dual button module, a breadboard, and some jumper wires to create a simple handheld console. You'll have to compile and flash the Retro-Go firmware, which was designed specifically for running games like Doom on ESP32-based devices. You can then load the specialized WAD (Where's All the Data) files. Kumar reports an average frame rate at a 320×240 resolution, which is very playable.

read more

Inspired by your shopping trends

  • Solar Power Manager For 12V Lead-Acid Battery

    The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and applica...

  • 5.5 V 1 watt solar panel

    Output voltage: 5.5 V, maximum current: 170 mA, connection: red-black cable with JST connector.

  • Mini solar cell 2V 200mA

    A small polycrystalline photovoltaic cell, ideal for conducting experiments with solar energy or LED applications.

  • Solar cell 1 V - 200 mA

    A small photovoltaic panel, ideal for conducting experiments with solar energy.

Compare products

0 of 3 items selected

Select first item to compare

Select second item to compare

Select third item to compare

Compare