Skip to content

    Your cart is empty

    Time to spark some excitement 🛒⚡

Taxes and shipping calculated at checkout
Subtotal €0,00

Grove - Dust Sensor(PPD42NS)

SKU TPX00056 Barcode 841454108498 Show more
Original price €9,44
Original price €9,44 - Original price €9,44
Original price €9,44
Current price €11,51
€11,51 - €11,51
Current price €11,51
VAT included

Try the new Grove - Dust Sensor (PPD42NS)!

Overview

Provide reliable data for air purifier system Easy maintenance PWM output Grove compatible interface Compact and light design.

This Dust Sensor gives a good indication of the air quality in an environment by measuring the dust concentration. The Particulate Matter level (PM level) in the air is measured by counting the Low Pulse Occupancy time (LPO time) in a given time unit. LPO time is proportional to PM concentration. This sensor can provide reliable data for air purifier systems; it is responsive to PM of diameter 1μm.

Note:

This sensor uses a counting method to measure dust concentration, not weighing method, and the unit is pcs/L or pcs/0.01cf.
Please pay attention to the warnings listed here.

Features:

  • Grove compatible interface(extra wire with connector)
  • Supply voltage range: 5V
  • Minimum detect particle: 1um
  • PWM output
  • Dimensions: 59(W)x45(H)x22(D) [mm]

Application Ideas:

  • Air Purifier
  • Air Quality Monitor
  • Air Conditioner
  • Ventilator

Get Inspired

PROJECT HUB
Claw prosthesis controlled by myoelectric sensor
Claw prosthesis controlled by myoelectric sensor
Project Tutorial by luiz_coppini

Print a claw on your 3D printer and use a myoelectric sensor to control it.

read more
BLOG
Your Arduino Nano ESP32 can run Doom
Your Arduino Nano ESP32 can run Doom
September 12, 2023

"But can it run Doom?" is more than just a joke in the tech world. It is also a decent litmus test for the computing power of hardware. That test isn't very relevant for modern computers, but it is still worth asking when discussing microcontrollers. Microcontrollers vary in dramatically in processing power and memory, with models to suit every application. But if you have an Arduino Nano ESP32 board, you can run Doom as Naveen Kumar has proven. The Nano ESP32 is a small IoT development board for the ESP32-S3 microcontroller, featuring Wi-Fi® and Bluetooth® connectivity. It also has a relatively high clock speed and quite a lot of memory: 240MHz and 512kB SRAM, respectively. That still isn't enough to meet the requirements of the original Doom release, which needed a lot more RAM. But Kumar demonstrates the use of an MCU-friendly port that runs well on this more limited hardware. Want to give it a try yourself? You'll need the Nano ESP32, an Adafruit 2.8" TFT LCD shield, an M5Stack joystick, a Seeed Studio Grove dual button module, a breadboard, and some jumper wires to create a simple handheld console. You'll have to compile and flash the Retro-Go firmware, which was designed specifically for running games like Doom on ESP32-based devices. You can then load the specialized WAD (Where's All the Data) files. Kumar reports an average frame rate at a 320×240 resolution, which is very playable.

read more

Inspired by your shopping trends

  • Grove - Gas Sensor (MQ9)

    It can detect combustible Carbon Monoxide, Coal Gas and Liquefied Gas. The sensitivity can be adjusted by the potentiometer. Hardware Overview This is an Analog output sensor. It needs to be conn...

  • Grove - Dust Sensor

    This Dust Sensor gives a good indication of the air quality in an environment by measuring the dust concentration. The Particulate Matter level (PM level) in the air is measured by counting the Low...

  • Grove - Barometer Sensor (BMP280)

    It can widely measure pressure ranging from 300 mbar to 1200 mbar, with a super high accuracy of 0.01mbar(0.1m) in ultra-high resolution mode. The chip only accepts 1.8V to 3.6V input voltage. Howe...

  • Speed control for DC motors from 3 to 35V 5A

    Also ideal for adjusting the brightness of LED lights and strips.

Compare products

0 of 3 items selected

Select first item to compare

Select second item to compare

Select third item to compare

Compare