Skip to content

    Your cart is empty

    Time to spark some excitement 🛒⚡

Taxes and shipping calculated at checkout
Subtotal €0,00

Grove - Temperature Sensor

SKU C000179 Barcode 101020015 Show more
Original price €0
Original price €3,02 - Original price €3,02
Original price
Current price €3,02
€3,02 - €3,02
Current price €3,02
VAT included

The Grove - Temperature Sensor uses a Thermistor to detect the ambient temperature.

Overview

The resistance of a thermistor will increase when the ambient temperature decreases. It’s this characteristic that we use to calculate the ambient temperature. The detectable range of this sensor is -40 - 125ºC, and the accuracy is ±1.5ºC


Tech specs

  • Voltage: 3.3 ~ 5V
  • Zero power resistance: 100 KΩ
  • Resistance Tolerance: ±1%
  • Operating temperature range: -40 ~ +125 ℃
  • Nominal B-Constant: 4250 ~ 4299K

Get Inspired

PROJECT HUB
Claw prosthesis controlled by myoelectric sensor
Claw prosthesis controlled by myoelectric sensor
Project Tutorial by luiz_coppini

Print a claw on your 3D printer and use a myoelectric sensor to control it.

read more
BLOG
Your Arduino Nano ESP32 can run Doom
Your Arduino Nano ESP32 can run Doom
September 12, 2023

"But can it run Doom?" is more than just a joke in the tech world. It is also a decent litmus test for the computing power of hardware. That test isn't very relevant for modern computers, but it is still worth asking when discussing microcontrollers. Microcontrollers vary in dramatically in processing power and memory, with models to suit every application. But if you have an Arduino Nano ESP32 board, you can run Doom as Naveen Kumar has proven. The Nano ESP32 is a small IoT development board for the ESP32-S3 microcontroller, featuring Wi-Fi® and Bluetooth® connectivity. It also has a relatively high clock speed and quite a lot of memory: 240MHz and 512kB SRAM, respectively. That still isn't enough to meet the requirements of the original Doom release, which needed a lot more RAM. But Kumar demonstrates the use of an MCU-friendly port that runs well on this more limited hardware. Want to give it a try yourself? You'll need the Nano ESP32, an Adafruit 2.8" TFT LCD shield, an M5Stack joystick, a Seeed Studio Grove dual button module, a breadboard, and some jumper wires to create a simple handheld console. You'll have to compile and flash the Retro-Go firmware, which was designed specifically for running games like Doom on ESP32-based devices. You can then load the specialized WAD (Where's All the Data) files. Kumar reports an average frame rate at a 320×240 resolution, which is very playable.

read more

Inspired by your shopping trends

  • Grove - Light Sensor v1.2

    The resistance of photoresistor decreases when the intensity of light increases. A dual OpAmp chip LM358 on board produces voltage corresponding to intensity of light(i.e. based on resistance value...

  • Grove - Barometer Sensor (BMP280)

    It can widely measure pressure ranging from 300 mbar to 1200 mbar, with a super high accuracy of 0.01mbar(0.1m) in ultra-high resolution mode. The chip only accepts 1.8V to 3.6V input voltage. Howe...

  • Grove - Gas Sensor (O2)

    You can see the current oxygen concentration from reading the voltage values output proportional to the concentration of oxygen on the oxygen concentration linear characteristic graph. It’s suitabl...

  • Grove - Digital Light Sensor

    Different from traditional analog light sensor, as Grove - Light Sensor, this digital module features a selectable light spectrum range due to its dual light sensitive diodes: infrared and full spe...

Compare products

0 of 3 items selected

Select first item to compare

Select second item to compare

Select third item to compare

Compare