
Seeed
-
€2,69| /
This shield pulls out the pins of the motherboard and expands to 8 Grove connectors, including 3 Grove digital connectors, 3 Grove analog connectors, 1 Grove I2C connector, and 1 Grove UART connector. With the help of the Grove system, you can connect hundreds of Grove sensors, Grove actuators a...
View full details€2,69| / -
€3,65| /
Grove Base Shield provides a simple way to connect with Arduino boards and help you get rid of breadboard and jumper wires. With the 16 on-board Grove Connectors, you can easily connect with over 300 Grove modules! The pinout of Base Shield V2 is compatible with the Arduino UNO, Arduino Leonardo ...
View full details€3,65| / -
€7,30| /
Grove-Temperature & Humidity Sensor Pro is a high accuracy temperature and humidity sensor based on the DHT22 module (also known as AM2302 or RHT03). High-cost performance and high precision make it ideal for temperature and humidity monitoring of Arduino and Raspberry Pi, you can also use it...
View full details€7,30| / -
€3,07| /
This sensor is very simple to use, you insert in into the soil and read the data. With this sensor in the right project, your plants can let you know when it's time to water them. Features: Soil moisture sensor based on soil resistivity measurement Easy to use 2.0 cm X 6.0 cm grove module
€3,07| / -
€1,85| /
The resistance of photoresistor decreases when the intensity of light increases. A dual OpAmp chip LM358 on board produces voltage corresponding to intensity of light(i.e. based on resistance value). The output signal is an analog value, the brighter the light is, the larger the value. This modul...
View full details€1,85| / -
€19,90| /
This module can be used to measure temperature, atmospheric pressure and humidity accurately and fast. As the atmospheric pressure changes with altitude, it can also measure approximate altitude of a place. It can be connected to a microcontroller with I2C (integrated with Grove socket) or throug...
View full details€19,90| / -
€2,97| /
The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace. Believe it or not this circuit will work with the digital I/O pins of your Arduino or you can use it with the analog pins...
View full details€2,97| / -
€9,20| /
The sensor(chip) used in the module is designed with Sensirion’s CMOSens® technology. The chip is well calibrated, linearized and compensated for digital output. The typical accuracy of this module can be ±2%RH (for relative humidity) and ±0.3°C (for temperature). This module is compatible with ...
View full details€9,20| / -
Save 50%
Original price €94,80Current price €47,40| /Beyond the Grove Shield is a bunch of Grove sensors and actuators with build-in Grove interfaces, makes your prototyping faster and easier. Simply plug in the modules and you are ready to create. Features: Various sensors and actuators Plug-and-play modules Works on a variety of Arduino-com...
View full detailsOriginal price €94,80Current price €47,40| / -
€1,58| /
We've already released the Grove - I2C Hub (4 Port), now comes the 6 port version, the same size, two more connectors, almost half the price! As you may know, the 7 address length I2C bus allows up to 128 I2C devices to access. At present, there are over 80 Grove I2C modules in Seeed, however, no...
View full details€1,58| / -
€5,02| /
The main component of the module is a simple microphone, which is based on the LM386 amplifier and an electret microphone. This module’s output is analog and can be easily sampled and tested by an Arduino. Features: Easy to use Provides analog output signal Easily integrates with Logic modu...
View full details€5,02| / -
€6,04| /
A 4 digit display module usually uses 12 pins. In this Grove gadget the TM1637 is used to scale down the control pins into two Grove pins. This way It only takes two digital pins from an Arduino to control the content on the display, this even includes the luminance of the display. For projects t...
View full details€6,04| / -
Sold out
€16,03| /The visible portion of the OLED measures 1.12” diagonally and contains 96x96 grayscale pixels. Because the display uses OLEDs, there is no backlight, and the contrast is very high. This OLED uses the SSD1327 driver chip, which manages the display. You can communicate to the driver chip using 4-wi...
View full details€16,03| / -
€6,04| /
Different from traditional analog light sensor, as Grove - Light Sensor, this digital module features a selectable light spectrum range due to its dual light sensitive diodes: infrared and full spectrum.You can choose among three detection modes when taking your readings. There is infrared mode, ...
View full details€6,04| / -
€7,40| /
The Grove - I2C Motor Driver (TB6612FNG) can drive two DC motors up to 12V/1.2A or one stepper motor up to 12V/1.2A. With the on-board MCU, it easily works with Arduino via the Grove I2C interface. This diver board is based on TB6612FNG, which is a driver IC for DC motor and stepper motor with o...
View full details€7,40| / -
€27,60| /
It is commonly found on modern machine tools and as an automotive diagnostic bus. Thanks to the CAN-BUS, makers are able to hack their cars! It adopts MCP2515 CAN-BUS controller with SPI interface and MCP2551 CAN transceiver to give you Arduino CAN-BUS capability. Default pinout is OBD-II and C...
View full details€27,60| / -
€4,93| /
The sensor consists of an IR LED and a photo sensor (phototransistor). The light emitted by the IR LED gets reflected by any object placed in front of the sensor and this reflection is detected by the photo sensor (phototransistor). Any white (or lighter) colored surface reflects more than black ...
View full details€4,93| / -
€14,22| /
This sensor SharpGP2Y0A21YK, boasts a small package and very low current consumption, takes a continuous distance reading and returns a corresponding analog voltage with a range of 10cm (4") to 80cm (30"). It can be used in TVs, personal computers, cars and so on. Features: Grove interface co...
View full details€14,22| / -
€5,44| /
The X and Y axes are two ~10k potentiometers which control 2D movement by generating analog signals. The joystick also has a push button that could be used for special applications. When the module is in working mode, it will output two analog values, representing two directions. Compared to a no...
View full details€5,44| /