Skip to content
Sensors & Environment

Sensors & Environment

  • €70,00

    Cicerone allows to build tracking applications around the world with meter-level accuracy and to communicate long-range, low-power data via LoRaWAN. The integrated Li-Po charging circuit enables the board to manage battery charging through the USB port. It is based on u-blox MAXM10S GNSS and Mo...

    View full details
    €70,00
  • Sold out
    €13,77

    It is suitable for detecting Alcohol, Benzine, CH4, Hexane, LPG, CO. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer. Note: The sensor value only reflects the approximated ...

    View full details
  • Sold out
    €7,93

    It is built with MQ303A semiconductor alcohol sensor. It has good sensitivity and fast response to alcohol, making it suitable for building a breathalyzer. This Grove module implements all the necessary circuitry for the MQ303A, such as power conditioning and heater power supply. This sensor outp...

    View full details
  • Sold out
    €8,80

    Grove - DPS310 is a high precision barometric pressure sensor, it can measure air pressure change caused by height changes in the centimeter level. Typical Applications: Indoor Navigation (floor detection e.g. in shopping malls and parking garages) Health and Sports (accurate elevation gain ...

    View full details
  • Sold out
    €74,94

    DFRobot released its latest wide range Arduino infrared CO2 sensor, which effective range is up to 0~50000ppm. This sensor is based on non-dispersive infrared (NDIR) technology and has good selectivity and oxygen-free dependency. It integrates temperature compensation and support UART communicati...

    View full details
  • €13,20

    Provide reliable data for air purifier system Easy maintenance PWM output Grove compatible interface Compact and light design. This Dust Sensor gives a good indication of the air quality in an environment by measuring the dust concentration. The Particulate Matter level (PM level) in the air is ...

    View full details
    €13,20
  • €70,70

    DFRobot Gravity: analog electrical conductivity meter V2 is specially used to measure the electrical conductivity of an aqueous solution, and then to evaluate the water quality, which is often used in water culture, aquaculture, environmental water detection, and other fields. You may also check ...

    View full details
    €70,70
  • €60,10

    HuskyLens is an easy-to-use AI machine vision sensor. It is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, color recognition, and tag(QR code) recognition. Through the UART / I2C port, HuskyLens can connect yout Arduino board lik...

    View full details
    €60,10
  • €57,00

    Great and powerful sensor for everyone that wants to know the exact concentration of CO2(Carbon Dioxide) in the air.  This is the first CO2 sensor compatible with Arduino. The output voltage of the module falls as the concentration of the CO2 increases. The potentiometer onboard is designed to s...

    View full details
    €57,00
  • Sold out
    €6,00

    This soil Moisture sensor is made of a corrosion resistant material giving it a long service life. Insert it into soil and impress your friends with the real-time soil moisture data! The product includes an on-board voltage regulator which gives it an operating voltage range of 3.3 ~ 5.5V. It is ...

    View full details
  • €3,50

    The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace. Believe it or not this circuit will work with the digital I/O pins of your Arduino or you can use it with the analog pins...

    View full details
    €3,50
  • €4,40

    It can detect the change in capacitance when a finger is nearby. This means no matter if your finger directly touches the pad or just stays close to the pad, the Grove - Touch Sensor will output HIGH.  

    €4,40
  • €3,30

    The resistance of a thermistor will increase when the ambient temperature decreases. It’s this characteristic that we use to calculate the ambient temperature. The detectable range of this sensor is -40 - 125ºC, and the accuracy is ±1.5ºC

    €3,30
  • €11,20

    Grove-Temperature & Humidity Sensor Pro is a high accuracy temperature and humidity sensor based on the DHT22 module (also known as AM2302 or RHT03). High-cost performance and high precision make it ideal for temperature and humidity monitoring of Arduino and Raspberry Pi, you can also use it...

    View full details
    €11,20
  • €13,40

    The sensor(chip) used in the module is designed with Sensirion’s CMOSens® technology. The chip is well calibrated, linearized and compensated for digital output. The typical accuracy of this module can be ±2%RH (for relative humidity) and ±0.3°C (for temperature). This module is compatible with ...

    View full details
    €13,40
  • Sold out
    €12,90

    This is a multifunctional sensor that gives you temperature and relative humidity information at the same time. It utilizes a TH02 sensor that can meet measurement needs of general purposes. It provides reliable readings when environment humidity condition inbetween 0-80% RH, and temperature con...

    View full details
  • €19,90

    This module can be used to measure temperature, atmospheric pressure and humidity accurately and fast. As the atmospheric pressure changes with altitude, it can also measure approximate altitude of a place. It can be connected to a microcontroller with I2C (integrated with Grove socket) or throug...

    View full details
    €19,90
  • €12,30

    This device is based on SI1145, a new sensor from SiLabs. The Si1145 is a low-power, reflectance-based, infrared proximity, UV index and ambient light sensor with I2C digital interface and programmable-event interrupt output. This device offers excellent performance under a wide dynamic range and...

    View full details
    €12,30
  • €5,60

    The main component of the module is a simple microphone, which is based on the LM386 amplifier and an electret microphone. This module’s output is analog and can be easily sampled and tested by an Arduino. Features: Easy to use Provides analog output signal Easily integrates with Logic modu...

    View full details
    €5,60
  • Sold out
    €3,30

    Through it, you can control a circuit of high voltage with low voltage, say 5V on the controller. There is an indicator LED on the board, which will light up when the controlled terminals get closed.

  • Sold out
    €9,60

    Simply connect it to Grove - Base shield and program it, when anyone moves in its detecting range, the sensor will output HIGH on its SIG pin. Features: Grove compatible interface Adjustable detecting distance Adjustable holding time

  • €5,90

    This sensor is very simple to use, you insert in into the soil and read the data. With this sensor in the right project, your plants can let you know when it's time to water them. Features: Soil moisture sensor based on soil resistivity measurement Easy to use 2.0 cm X 6.0 cm grove module

    €5,90
  • €3,30

    The resistance of photoresistor decreases when the intensity of light increases. A dual OpAmp chip LM358 on board produces voltage corresponding to intensity of light(i.e. based on resistance value). The output signal is an analog value, the brighter the light is, the larger the value. This modul...

    View full details
    €3,30
  • Sold out
    €6,70

    The module consists of an IR LED and a photosensor (phototransistor) pair. The light emitted by the IR LED gets reflected by any object placed in front of the sensor and this reflection is detected by the photosensor(phototransistor). Any white (or lighter) colored surface reflects more than blac...

    View full details
x