Expand your capabilities

DFRobot Gravity: analog electrical conductivity meter V2 is specially used to measure the electrical conductivity of an aqueous solution, and then to evaluate the water quality, which is often used in water culture, aquaculture, environmental water detection, and other fields. You may also check ...

DYNAMIXEL Shield for Arduino MKR allows users to easily use ROBOTIS’ DYNAMIXEL Series along with Arduino MKR Boards. The features are as follows: Compatible with Arduino MKR Compatible with ROBOTIS DYNAMIXEL TTL Series (Discontinued DYNAMIXEL may not be supported) For 12V DYNAMIXEL power su...

Grove - RGB LED Stick (15-WS2813 Mini) is a cost-effective full color LED stick with 15 chainable and programmable WS2813 mini LEDs. This Grove - RGB LED stick is similar to Grove - RGB LED stick (10-WS2813 Mini) but more in the number of LEDs. It contains 15 LEDs. You can control these 15 LE...

Grove - DPS310 is a high precision barometric pressure sensor, it can measure air pressure change caused by height changes in the centimeter level. Typical Applications: Indoor Navigation (floor detection e.g. in shopping malls and parking garages) Health and Sports (accurate elevation gain ...

Provide reliable data for air purifier system Easy maintenance PWM output Grove compatible interface Compact and light design. This Dust Sensor gives a good indication of the air quality in an environment by measuring the dust concentration. The Particulate Matter level (PM level) in the air is ...

DFRobot released its latest wide range Arduino infrared CO2 sensor, which effective range is up to 0~50000ppm. This sensor is based on non-dispersive infrared (NDIR) technology and has good selectivity and oxygen-free dependency. It integrates temperature compensation and support UART communicati...

Fast robotics prototyping made simple thanks to this expansion shield. No need of soldering and wiring, things that often becomes an issue when a bridged connection happens and components break. Often, without this solution, robot prototyping or electronics DIY becomes a very long term project. ...

DFPlayer mini MP3 player is a small and low cost MP3 module player with a simplified output directly to the speaker. The module can be used as a standalone module with attached battery, speaker and push buttons or used in combination with an Arduino UNO or any other with RX/TX capabilities. It pe...

In many applications, lithium batteries are used as our power solutions. In this kind of application, the most two important things are the power boost and battery charger. These two points are a prerequisite for the system. The traditional power boost and battery charge circuit are usually divid...

This is a 20W adjustable DC-DC buck converter module with digital display. It is based on LM2596 3A step-down voltage regulator and supports an input of 0~40V DC with an accuracy of ± 0.05V. On a regular buck converter there is no display and you have to measure the output manually with a multim...

This Power Module is a small size 5A 350KHz 25V Buck DC to DC Converter. It can convert any DC voltage between 3.6V-25V to a selectable voltage from 3.3V to 25V. You can choose 5V direct output voltage with the switch or adjust the output voltage by the blue&white resistor. It is convenient f...

This is a photoelectric water liquid level sensor that operates using optical principles. The advantages of this photoelectric water liquid level sensor are good sensitivity and no need for mechanical parts - meaning less calibration! The corrosion resistant probe is easily mounted and can handle...

The J-Link 19-pin Cortex-M Adapter may also be used to connect J-Link to a non Cortex-M target as far as the target connector uses the same pinout as shown below. By default, TRST is not connected, but the Cortex-M Adapter comes with a solder bridge (NR1) which allows TRST to be connected to pin ...

SEGGER J-Link BASE Compact:   Supports a broad range of microcontrollers  Supports direct download into RAM and flash memory Multiple CPUs supported—8051, PIC32, RX, ARM7/9/11, Cortex-M/R/A, RISC-V  Download speed up to 1 MByte/s Supports unlimited breakpoints in flash memory, additional l...

Get the SEGGER J-Link PLUS Compact debug probe: a compact version of the J-Link PLUS. Mounts securely & unobtrusively into development and end user equipment. Based on 32-bit RISC CPU, it communicates at high speed with supported target CPUs. Thanks to a small size with two mounting holes, it...

Get the J-Link EDU Mini, offering the same functionality as the J-Link EDU but in a reduced form factor. The J-Link EDU Mini Classroom Edition includes twelve J-Link EDU Mini units on special offer. Designed for education purposes and hobbyists, it provides access to top-of-the-line debug probe f...

It is suitable for detecting Alcohol, Benzine, CH4, Hexane, LPG, CO. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer. Note: The sensor value only reflects the approximated ...

It is built with MQ303A semiconductor alcohol sensor. It has good sensitivity and fast response to alcohol, making it suitable for building a breathalyzer. This Grove module implements all the necessary circuitry for the MQ303A, such as power conditioning and heater power supply. This sensor outp...

The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and application engineers. This medium-power high-efficiency solar power management module allows you to charg...

Some RS485 shields for the Arduino are not suitable for professional use, because they come without galvanic isolation between the RS485 bus and the Arduino. Without such isolation, it's possible to damage the Arduino or cause a malfunction of the device due to the large distances of an RS485 bu...

Note: This item is a kit which requires assembly and soldering. Different Arduino MKR Shields can be used via our HAT as an extension for the Raspberry Pi. Furthermore, Arduino offers different Arduino boards for different IoT networks like Sigfox, Lora, NB-IOT. These boards can be used as a mo...

Grove Base Shield provides a simple way to connect with Arduino boards and help you get rid of breadboard and jumper wires. With the 16 on-board Grove Connectors, you can easily connect with over 300 Grove modules! The pinout of Base Shield V2 is compatible with the Arduino UNO, Arduino Leonardo ...

The Nano I/O Sensor Shield is an expansion board for the Arduino Nano. There are several different options for power input. The form factor of the Nano I/O Shield board is the same as the Arduino UNO/Arduino Leonardo. In addition, the sensor shield adopts Gravity interface that each pinout includ...