Seeed

This shield pulls out the pins of the motherboard and expands to 8 Grove connectors, including 3 Grove digital connectors, 3 Grove analog connectors, 1 Grove I2C connector, and 1 Grove UART connector. With the help of the Grove system, you can connect hundreds of Grove sensors, Grove actuators a...

Grove Base Shield provides a simple way to connect with Arduino boards and help you get rid of breadboard and jumper wires. With the 16 on-board Grove Connectors, you can easily connect with over 300 Grove modules! The pinout of Base Shield V2 is compatible with the Arduino UNO, Arduino Leonardo ...

Grove-Temperature & Humidity Sensor Pro is a high accuracy temperature and humidity sensor based on the DHT22 module (also known as AM2302 or RHT03). High-cost performance and high precision make it ideal for temperature and humidity monitoring of Arduino and Raspberry Pi, you can also use it...

Simply connect it to Grove - Base shield and program it, when anyone moves in its detecting range, the sensor will output HIGH on its SIG pin. Features: Grove compatible interface Adjustable detecting distance Adjustable holding time

Through it, you can control a circuit of high voltage with low voltage, say 5V on the controller. There is an indicator LED on the board, which will light up when the controlled terminals get closed.

This sensor is very simple to use, you insert in into the soil and read the data. With this sensor in the right project, your plants can let you know when it's time to water them. Features: Soil moisture sensor based on soil resistivity measurement Easy to use 2.0 cm X 6.0 cm grove module

The resistance of photoresistor decreases when the intensity of light increases. A dual OpAmp chip LM358 on board produces voltage corresponding to intensity of light(i.e. based on resistance value). The output signal is an analog value, the brighter the light is, the larger the value. This modul...

The resistance of a thermistor will increase when the ambient temperature decreases. It’s this characteristic that we use to calculate the ambient temperature. The detectable range of this sensor is -40 - 125ºC, and the accuracy is ±1.5ºC

Compared to LCD, OLED screens have a number of advantages such as high brightness, self-emission, high contrast ratio, slim / thin outline, wide viewing angle, wide temperature range, and low power consumption. Features: Grove compatible Interface Communicate Mode: I2C Low power consumption...

Grove - DPS310 is a high precision barometric pressure sensor, it can measure air pressure change caused by height changes in the centimeter level. Typical Applications: Indoor Navigation (floor detection e.g. in shopping malls and parking garages) Health and Sports (accurate elevation gain ...

This module can be used to measure temperature, atmospheric pressure and humidity accurately and fast. As the atmospheric pressure changes with altitude, it can also measure approximate altitude of a place. It can be connected to a microcontroller with I2C (integrated with Grove socket) or throug...

The piezo can be connected to digital outputs, and will emit a tone when the output is high. Alternatively it can be connected to an analog pulse-width modulation output to generate various tones and effects.  Grove - Buzzer is a simple yet enjoyable twig to use. It can output noise at a volume ...

The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace. Believe it or not this circuit will work with the digital I/O pins of your Arduino or you can use it with the analog pins...

Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Grove modules to the Basic Shield or to other Grove compatible boards for quick prototyping. 50 cm cables

The sensor(chip) used in the module is designed with Sensirion’s CMOSens® technology. The chip is well calibrated, linearized and compensated for digital output. The typical accuracy of this module can be ±2%RH (for relative humidity) and ±0.3°C (for temperature). This module is compatible with ...

This sensor is designed for comprehensive monitor over indoor air condition. It's responsive to a wide scope of harmful gases, as carbon monoxide, alcohol, acetone, thinner, formaldehyde and so on. Due to the measuring mechanism, this sensor can't output specific data to describe target gases' co...

This is a multifunctional sensor that gives you temperature and relative humidity information at the same time. It utilizes a TH02 sensor that can meet measurement needs of general purposes. It provides reliable readings when environment humidity condition inbetween 0-80% RH, and temperature con...

We've already released the Grove - I2C Hub (4 Port), now comes the 6 port version, the same size, two more connectors, almost half the price! As you may know, the 7 address length I2C bus allows up to 128 I2C devices to access. At present, there are over 80 Grove I2C modules in Seeed, however, no...

The main component of the module is a simple microphone, which is based on the LM386 amplifier and an electret microphone. This module’s output is analog and can be easily sampled and tested by an Arduino. Features: Easy to use Provides analog output signal Easily integrates with Logic modu...

A 4 digit display module usually uses 12 pins. In this Grove gadget the TM1637 is used to scale down the control pins into two Grove pins. This way It only takes two digital pins from an Arduino to control the content on the display, this even includes the luminance of the display. For projects t...

Different from traditional analog light sensor, as Grove - Light Sensor, this digital module features a selectable light spectrum range due to its dual light sensitive diodes: infrared and full spectrum.You can choose among three detection modes when taking your readings. There is infrared mode, ...

The Grove - I2C Motor Driver (TB6612FNG) can drive two DC motors up to 12V/1.2A or one stepper motor up to 12V/1.2A. With the on-board MCU, it easily works with Arduino via the Grove I2C interface. This diver board is based on TB6612FNG, which is a driver IC for DC motor and stepper motor with o...

The visible portion of the OLED measures 1.12” diagonally and contains 96x96 grayscale pixels. Because the display uses OLEDs, there is no backlight, and the contrast is very high. This OLED uses the SSD1327 driver chip, which manages the display. You can communicate to the driver chip using 4-wi...

It is commonly found on modern machine tools and as an automotive diagnostic bus. Thanks to the CAN-BUS, makers are able to hack their cars!  It adopts MCP2515 CAN-BUS controller with SPI interface and MCP2551 CAN transceiver to give you Arduino CAN-BUS capability. Default pinout is OBD-II and C...

It can detect combustible Carbon Monoxide, Coal Gas and Liquefied Gas. The sensitivity can be adjusted by the potentiometer. Hardware Overview This is an Analog output sensor. It needs to be connected to any one Analog socket in Grove Base Shield. It is possible to connect the Grove module to A...

Provide reliable data for air purifier system Easy maintenance PWM output Grove compatible interface Compact and light design. This Dust Sensor gives a good indication of the air quality in an environment by measuring the dust concentration. The Particulate Matter level (PM level) in the air is ...

The sensor consists of an IR LED and a photo sensor (phototransistor). The light emitted by the IR LED gets reflected by any object placed in front of the sensor and this reflection is detected by the photo sensor (phototransistor). Any white (or lighter) colored surface reflects more than black ...

This sensor SharpGP2Y0A21YK, boasts a small package and very low current consumption, takes a continuous distance reading and returns a corresponding analog voltage with a range of 10cm (4") to 80cm (30"). It can be used in TVs, personal computers, cars and so on. Features: Grove interface co...

There is a continuous-time switch on this Grove module. The output from the module switches from low (turns on) when a magnetic field (south polarity) is perpendicular to the Hall sensor and when it passes the operate point threshold BOP it switches to high (turns off) when the magnetic field dis...

It can detect the change in capacitance when a finger is nearby. This means no matter if your finger directly touches the pad or just stays close to the pad, the Grove - Touch Sensor will output HIGH.  

Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Grove modules to the Basic Shield or to other Grove compatible boards for quick prototyping. 30 cm cables

The X and Y axes are two ~10k potentiometers which control 2D movement by generating analog signals. The joystick also has a push button that could be used for special applications. When the module is in working mode, it will output two analog values, representing two directions. Compared to a no...

The module consists of an IR LED and a photosensor (phototransistor) pair. The light emitted by the IR LED gets reflected by any object placed in front of the sensor and this reflection is detected by the photosensor(phototransistor). Any white (or lighter) colored surface reflects more than blac...